|
NAME | SYNOPSIS | DESCRIPTION | VERSIONS | CONFORMING TO | NOTES | SEE ALSO | COLOPHON |
|
EPOLL(7) Linux Programmer's Manual EPOLL(7)
NAME top
epoll - I/O event notification facility
SYNOPSIS top
#include
DESCRIPTION top
The epoll API performs a similar task to poll(2): monitoring multiple
file descriptors to see if I/O is possible on any of them. The epoll
API can be used either as an edge-triggered or a level-triggered
interface and scales well to large numbers of watched file
descriptors. The following system calls are provided to create and
manage an epoll instance:
* epoll_create(2) creates a new epoll instance and returns a file
descriptor referring to that instance. (The more recent
epoll_create1(2) extends the functionality of epoll_create(2).)
* Interest in particular file descriptors is then registered via
epoll_ctl(2). The set of file descriptors currently registered on
an epoll instance is sometimes called an epoll set.
* epoll_wait(2) waits for I/O events, blocking the calling thread if
no events are currently available.
Level-triggered and edge-triggered
The epoll event distribution interface is able to behave both as
edge-triggered (ET) and as level-triggered (LT). The difference
between the two mechanisms can be described as follows. Suppose that
this scenario happens:
1. The file descriptor that represents the read side of a pipe (rfd)
is registered on the epoll instance.
2. A pipe writer writes 2 kB of data on the write side of the pipe.
3. A call to epoll_wait(2) is done that will return rfd as a ready
file descriptor.
4. The pipe reader reads 1 kB of data from rfd.
5. A call to epoll_wait(2) is done.
If the rfd file descriptor has been added to the epoll interface
using the EPOLLET (edge-triggered) flag, the call to epoll_wait(2)
done in step 5 will probably hang despite the available data still
present in the file input buffer; meanwhile the remote peer might be
expecting a response based on the data it already sent. The reason
for this is that edge-triggered mode delivers events only when
changes occur on the monitored file descriptor. So, in step 5 the
caller might end up waiting for some data that is already present
inside the input buffer. In the above example, an event on rfd will
be generated because of the write done in 2 and the event is consumed
in 3. Since the read operation done in 4 does not consume the whole
buffer data, the call to epoll_wait(2) done in step 5 might block
indefinitely.
An application that employs the EPOLLET flag should use nonblocking
file descriptors to avoid having a blocking read or write starve a
task that is handling multiple file descriptors. The suggested way
to use epoll as an edge-triggered (EPOLLET) interface is as follows:
i with nonblocking file descriptors; and
ii by waiting for an event only after read(2) or write(2)
return EAGAIN.
By contrast, when used as a level-triggered interface (the default,
when EPOLLET is not specified), epoll is simply a faster poll(2), and
can be used wherever the latter is used since it shares the same
semantics.
Since even with edge-triggered epoll, multiple events can be
generated upon receipt of multiple chunks of data, the caller has the
option to specify the EPOLLONESHOT flag, to tell epoll to disable the
associated file descriptor after the receipt of an event with
epoll_wait(2). When the EPOLLONESHOT flag is specified, it is the
caller's responsibility to rearm the file descriptor using
epoll_ctl(2) with EPOLL_CTL_MOD.
Interaction with autosleep
If the system is in autosleep mode via /sys/power/autosleep and an
event happens which wakes the device from sleep, the device driver
will keep the device awake only until that event is queued. To keep
the device awake until the event has been processed, it is necessary
to use the epoll_ctl(2) EPOLLWAKEUP flag.
When the EPOLLWAKEUP flag is set in the events field for a struct
epoll_event, the system will be kept awake from the moment the event
is queued, through the epoll_wait(2) call which returns the event
until the subsequent epoll_wait(2) call. If the event should keep
the system awake beyond that time, then a separate wake_lock should
be taken before the second epoll_wait(2) call.
/proc interfaces
The following interfaces can be used to limit the amount of kernel
memory consumed by epoll:
/proc/sys/fs/epoll/max_user_watches (since Linux 2.6.28)
This specifies a limit on the total number of file descriptors
that a user can register across all epoll instances on the
system. The limit is per real user ID. Each registered file
descriptor costs roughly 90 bytes on a 32-bit kernel, and
roughly 160 bytes on a 64-bit kernel. Currently, the default
value for max_user_watches is 1/25 (4%) of the available low
memory, divided by the registration cost in bytes.
Example for suggested usage
While the usage of epoll when employed as a level-triggered interface
does have the same semantics as poll(2), the edge-triggered usage
requires more clarification to avoid stalls in the application event
loop. In this example, listener is a nonblocking socket on which
listen(2) has been called. The function do_use_fd() uses the new
ready file descriptor until EAGAIN is returned by either read(2) or
write(2). An event-driven state machine application should, after
having received EAGAIN, record its current state so that at the next
call to do_use_fd() it will continue to read(2) or write(2) from
where it stopped before.
#define MAX_EVENTS 10
struct epoll_event ev, events[MAX_EVENTS];
int listen_sock, conn_sock, nfds, epollfd;
/* Code to set up listening socket, 'listen_sock',
(socket(), bind(), listen()) omitted */
epollfd = epoll_create1(0);
if (epollfd == -1) {
perror("epoll_create1");
exit(EXIT_FAILURE);
}
ev.events = EPOLLIN;
ev.data.fd = listen_sock;
if (epoll_ctl(epollfd, EPOLL_CTL_ADD, listen_sock, &ev) == -1) {
perror("epoll_ctl: listen_sock");
exit(EXIT_FAILURE);
}
for (;;) {
nfds = epoll_wait(epollfd, events, MAX_EVENTS, -1);
if (nfds == -1) {
perror("epoll_wait");
exit(EXIT_FAILURE);
}
for (n = 0; n < nfds; ++n) {
if (events[n].data.fd == listen_sock) {
conn_sock = accept(listen_sock,
(struct sockaddr *) &addr, &addrlen);
if (conn_sock == -1) {
perror("accept");
exit(EXIT_FAILURE);
}
setnonblocking(conn_sock);
ev.events = EPOLLIN | EPOLLET;
ev.data.fd = conn_sock;
if (epoll_ctl(epollfd, EPOLL_CTL_ADD, conn_sock,
&ev) == -1) {
perror("epoll_ctl: conn_sock");
exit(EXIT_FAILURE);
}
} else {
do_use_fd(events[n].data.fd);
}
}
}
When used as an edge-triggered interface, for performance reasons, it
is possible to add the file descriptor inside the epoll interface
(EPOLL_CTL_ADD) once by specifying (EPOLLIN|EPOLLOUT). This allows
you to avoid continuously switching between EPOLLIN and EPOLLOUT
calling epoll_ctl(2) with EPOLL_CTL_MOD.
Questions and answers
Q0 What is the key used to distinguish the file descriptors
registered in an epoll set?
A0 The key is the combination of the file descriptor number and the
open file description (also known as an "open file handle", the
kernel's internal representation of an open file).
Q1 What happens if you register the same file descriptor on an epoll
instance twice?
A1 You will probably get EEXIST. However, it is possible to add a
duplicate (dup(2), dup2(2), fcntl(2) F_DUPFD) file descriptor to
the same epoll instance. This can be a useful technique for
filtering events, if the duplicate file descriptors are
registered with different events masks.
Q2 Can two epoll instances wait for the same file descriptor? If
so, are events reported to both epoll file descriptors?
A2 Yes, and events would be reported to both. However, careful
programming may be needed to do this correctly.
Q3 Is the epoll file descriptor itself poll/epoll/selectable?
A3 Yes. If an epoll file descriptor has events waiting, then it
will indicate as being readable.
Q4 What happens if one attempts to put an epoll file descriptor into
its own file descriptor set?
A4 The epoll_ctl(2) call will fail (EINVAL). However, you can add
an epoll file descriptor inside another epoll file descriptor
set.
Q5 Can I send an epoll file descriptor over a UNIX domain socket to
another process?
A5 Yes, but it does not make sense to do this, since the receiving
process would not have copies of the file descriptors in the
epoll set.
Q6 Will closing a file descriptor cause it to be removed from all
epoll sets automatically?
A6 Yes, but be aware of the following point. A file descriptor is a
reference to an open file description (see open(2)). Whenever a
file descriptor is duplicated via dup(2), dup2(2), fcntl(2)
F_DUPFD, or fork(2), a new file descriptor referring to the same
open file description is created. An open file description
continues to exist until all file descriptors referring to it
have been closed. A file descriptor is removed from an epoll set
only after all the file descriptors referring to the underlying
open file description have been closed (or before if the file
descriptor is explicitly removed using epoll_ctl(2)
EPOLL_CTL_DEL). This means that even after a file descriptor
that is part of an epoll set has been closed, events may be
reported for that file descriptor if other file descriptors
referring to the same underlying file description remain open.
Q7 If more than one event occurs between epoll_wait(2) calls, are
they combined or reported separately?
A7 They will be combined.
Q8 Does an operation on a file descriptor affect the already
collected but not yet reported events?
A8 You can do two operations on an existing file descriptor. Remove
would be meaningless for this case. Modify will reread available
I/O.
Q9 Do I need to continuously read/write a file descriptor until
EAGAIN when using the EPOLLET flag (edge-triggered behavior) ?
A9 Receiving an event from epoll_wait(2) should suggest to you that
such file descriptor is ready for the requested I/O operation.
You must consider it ready until the next (nonblocking)
read/write yields EAGAIN. When and how you will use the file
descriptor is entirely up to you.
For packet/token-oriented files (e.g., datagram socket, terminal
in canonical mode), the only way to detect the end of the
read/write I/O space is to continue to read/write until EAGAIN.
For stream-oriented files (e.g., pipe, FIFO, stream socket), the
condition that the read/write I/O space is exhausted can also be
detected by checking the amount of data read from / written to
the target file descriptor. For example, if you call read(2) by
asking to read a certain amount of data and read(2) returns a
lower number of bytes, you can be sure of having exhausted the
read I/O space for the file descriptor. The same is true when
writing using write(2). (Avoid this latter technique if you
cannot guarantee that the monitored file descriptor always refers
to a stream-oriented file.)
Possible pitfalls and ways to avoid them
o Starvation (edge-triggered)
If there is a large amount of I/O space, it is possible that by
trying to drain it the other files will not get processed causing
starvation. (This problem is not specific to epoll.)
The solution is to maintain a ready list and mark the file descriptor
as ready in its associated data structure, thereby allowing the
application to remember which files need to be processed but still
round robin amongst all the ready files. This also supports ignoring
subsequent events you receive for file descriptors that are already
ready.
o If using an event cache...
If you use an event cache or store all the file descriptors returned
from epoll_wait(2), then make sure to provide a way to mark its
closure dynamically (i.e., caused by a previous event's processing).
Suppose you receive 100 events from epoll_wait(2), and in event #47 a
condition causes event #13 to be closed. If you remove the structure
and close(2) the file descriptor for event #13, then your event cache
might still say there are events waiting for that file descriptor
causing confusion.
One solution for this is to call, during the processing of event 47,
epoll_ctl(EPOLL_CTL_DEL) to delete file descriptor 13 and close(2),
then mark its associated data structure as removed and link it to a
cleanup list. If you find another event for file descriptor 13 in
your batch processing, you will discover the file descriptor had been
previously removed and there will be no confusion.
VERSIONS top
The epoll API was introduced in Linux kernel 2.5.44. Support was
added to glibc in version 2.3.2.
CONFORMING TO top
The epoll API is Linux-specific. Some other systems provide similar
mechanisms, for example, FreeBSD has kqueue, and Solaris has
/dev/poll.
NOTES top
The set of file descriptors that is being monitored via an epoll file
descriptor can be viewed via the entry for the epoll file descriptor
in the process's /proc/[pid]/fdinfo directory. See proc(5) for
further details.
SEE ALSO top
epoll_create(2), epoll_create1(2), epoll_ctl(2), epoll_wait(2),
poll(2), select(2)
COLOPHON top
This page is part of release 4.12 of the Linux man-pages project. A
description of the project, information about reporting bugs, and the
latest version of this page, can be found at
https://www.kernel.org/doc/man-pages/.
Linux 2016-10-08 EPOLL(7)
Pages that refer to this page: accept(2), epoll_create(2), epoll_ctl(2), epoll_wait(2), eventfd(2), futex(2), perf_event_open(2), perfmonctl(2), poll(2), recv(2), select(2), select_tut(2), signalfd(2), timerfd_create(2), userfaultfd(2), sd-event(3), sd_event_add_io(3), sd_event_get_fd(3), proc(5), systemd.exec(5), capabilities(7), fanotify(7), inotify(7), mq_overview(7), pipe(7), udp(7)
Copyright and license for this manual page
|
HTML rendering created 2017-07-13 by Michael Kerrisk, author of The Linux Programming Interface, maintainer of the Linux man-pages project. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH.
|
|